Brembo brake master cylinder overhaul kit for handlebar, undertank (cable operated) mounted, handlebar mounted and rear PS 12 master cylinders. Contains seals, brake grease, spring and piston. PS12 handlebar master cylinder fitted to early 850 and 1000 models. PS12 rear master cylinder fitted to Nevada 750

This seal kit is also known as 082039797. NB repair kit instructions refer to rear master cylinder. To fit this to a PS12 handlebar mounted cylinder you will need to punch the old piston out using a thin drift through the hole at the banjo bolt end of the master cylinder. Carefully note the order of the ring and washer as the piston comes out and replace with components from kit. Brembo no. 110279720. See this link for help with fitting this kit

 2 in stock

 17659352 GU17659352 17 65 93 52
 1765 9352 1765.9352 17.65.93.52

Also fits Ducati 500 SL Pantah, Ducati 350/500 Twin GTV, Ducati 350/500 SL Pantah, Benelli 500 Quattro, Benelli 504 Sport, Benelli 250 2C, Benelli 900 Sei, Laverda Montjuic, Harris F1

Complete drilled fully floating stainless steel EBC Brake Disc. Used for rear and front left hand brake disc for Le Mans 1000, 1000S. Rear brake disc only on Cali 3, Cali 1100, Spada 3, Strada 1000

Also known as Guzzi ref 28613660, 30635860. This is an update to the non floating disc ( 28613300 / 28613301 ) fitted to front of Nevada, Lario, T5, SP II, Monza 2, V75 and V35 3. Always fit new brake pads when replacing a brake disc - BRA54724 . Use disc bolt BRA30460

 2 in stock

28613670-z 28613670 GU28613670 28 61 36 70
 2861 3670 2861.3670 28.61.36.70

Black 45 degree rubber cap for brakeline banjo union with master cylinder

Also used for cable exit from clip ons fitted to Le Mans 1 and Le Mans 2. Front brake light switch cover for ELA14959

 2 in stock

 39663801 GU39663801 39 66 38 01
 3966 3801 3966.3801 39.66.38.01

Brembo pad pin kit for Brembo F05 (P5) calipers. Contains one long pin, two short and retaining spring

Brembo ref. 120280010, also used on some Laverdas . Front calipers only on Strada

 2 in stock

 39659100 GU39659100 39 65 91 00
 3965 9100 3965.9100 39.65.91.00

Also fits Benelli 250 TS

Split pin for brake pedal pivot

 2 in stock

 95500227 GU95500227 95 50 02 27
 9550 0227 9550.0227 95.50.02.27

Stainless M10 x 1.25 steel banjo bolt, coarser thread (1.25) than most brake fittings. See BRA01001 for M10 x 1 banjo bolt for most other brake fittings and models

 2 in stock

Universal hydraulic brake light switch. This hydraulic switch replaces discontinued brakelight switches by bolting in place of a single banjo bolt on the handlebar or rear brake master cylinder

NB stop light switch may be supplied with or without 2 pin block connector. Can be used in place of Guzzi ref. 32657060

 1 in stock

Bare aluminium finish brake lever

 1 in stock

17605652-z 17605652 GU17605652 17 60 56 52
 1760 5652 1760.5652 17.60.56.52

Also fits Laverda

Rear external master cylinder return spring, bright finish

 1 in stock

19667600-z 19667600 GU19667600 19 66 76 00
 1966 7600 1966.7600 19.66.76.00

Complete drilled fully floating stainless steel EBC Brake Disc for front right hand side

Also known as Guzzi ref 28613660, 30635860. This is an update to the non floating disc ( 28613300 / 28613301 ) fitted to front of Nevada, Lario, T5, SP II, Monza 2, V75 and V35 3. Always fit new brake pads when replacing a brake disc. Use disc bolt BRA30460

 1 in stock

28613670-z 28613670 GU28613670 28 61 36 70
 2861 3670 2861.3670 28.61.36.70